W type high efficient wheat flour baking powder double cone mixer blender mixing machine

Introduction Double-cone mixer is often called W-type rotary vacuum dryer , which is widely used in medicine, food, chemical industry, pesticides, dyes, rare earths, new energy and other powder mixing process industries. Features: 1, the volume can be customized, the mixing effect is good, the self-flipping movement of the cylinder caused by axial rotation makes the material mixing uniformity reach more than 99.5%, and the mixing time is short 2. Special materials can increase the stirring rod in the body of the cylinder to accelerate the rapid and uniform mixing of the materials. 3. The cylinder can be configured with heating, heat preservation, cooling and other functions 4. A variety of closed feeding methods are preferred for feeding, and the caliber can realize seamless docking of sealing, and the automatic docking of feeding equipment and cylinder can also be realized 5. The discharge method is reasonable and efficient, so as to achieve no residue of the material, and the discharge is more thorough and stable Selection Points: a.Full capacity of equipment: 50L~10000L; b.Mixed volume ratio of equipment: > 60% full load rate; c.The mixing time used can be set; d.Drive configuration power 1.5KW-55KW; e.Equipment materials can be 316L, 321, 304, carbon steel, and lining, etc.;

Products Details

Double cone mixer is a new efficient fine container rotary, agitation type mixing equipment, for the uniform mixing of various powdery and granular materials, with a high degree of mixing, the amount of added ingredients can also achieve a better degree of mixing; The machine adopts mechanical seal, the powder will not leak, and the bearing service life is long; The machine has high mixing efficiency, high work efficiency, low labor intensity and convenient operation.Double cone mixer by double cone cylinder, mechanical seal, frame, deceleration transmission, etc., rotating double cone cylinder so that the material in the cylinder body produces disorder rolling mixing, so that the material in the cylinder body quickly mixed, mixing barrel can be arbitrarily tilted angle, easy to discharge and cleaning needs. 1. Let heat source (for example, low pressure steam or heat conduct oil) pass through the sealed jacket. The heat will be transmitted to raw material to be dried through inner shell; 2. Under driving of power, the tank is rotated slowly and the raw material inside it is mixed continuously. The purpose of reinforced drying can     e realizd; 3. The raw material exists at the state of vacuum. The drop of team pressure makes the moisture (solvent) at the surface of raw material become saturation and will evaporate. The solvent will be discharged through vacuum pump an drecovered in time. The inner moisture (solvent) of raw material will infiltrate, evaporate and discharge continuously. The three processes are carried out unceasingly and the purpose of drying can be realized within a short time.1. The operator must be trained and qualified, and the equipment can only be operated after being authorized by the person in charge of the post. 2. The first time the equipment is started, the supplier's professionals need to be authorized or debugged on the spot. 3. There are certain dangers and hazards in the operation of the equipment, please operate with caution. 4. In order to ensure that the contents of the box are not polluted, the equipment needs to be installed in the workplace of the appropriate cleanliness level. 5. Before starting the machine for the first time, please clean up the environmental hygiene and equipment hygiene. 6. Users need to formulate relevant sanitary treatment procedures to ensure the quality of equipment work. 7. The electrical components of the double cone mixer are strictly forbidden to use water flushing method for cleaning and hygiene, please pay attention when using. In the case of power outage, it is required to clean the control cabinet/operation cabinet with a wet rag that does not shed fibers and does not contain combustible solvents or compressed air without water and oil, and wait for it to dry before it can be delivered to the operation. 8. When operating the double cone mixer, it should be operated independently by a single person, and it is strictly forbidden to cooperate with the two people to operate to prevent bumping and squeezing injury. 9. During the operation of the double cone mixer, if the parameter control is improper or the system components are out of balance, it may produce certain dangers, so it is forbidden to be unattended. 10. The barrel should avoid hard object tapping to prevent the cylinder from deforming and affecting the smooth operation.

Model

Full volume of mixing drum(L)

Loading coefficient

Motor power(kw)

Overall dimension (length × Wide × High)(mm)

Machine weight(Kg)

CFW-2

2

40%-60%

0.09

500×200×300

40

CFW-5

5

0.2

650×250×450

60

CFW-10

10

0.37

800×300×600

100

CFW-20

20

0.55

980×400×850

180

CFW-50

50

0.75

1350×500×1100

380

CFW-100

100

1.1

1580×650×1350

550

CFW-200

200

1.5

1800×750×1650

680

CFW -300

300

2.2

2050×850×1850

800

CFW -400

400

3

2300×950×1850

1000

CFW -500

500

4

2400×1050×2100

1200

CFW -800

800

5.5

2500×1200×2300

1400

CFW -1000

1000

5.5

2800×1500×2500

1800

CFW -2000

2000

7.5

3400×1600×2700

2100

CFW-3000

3000

11

3500×1680×2900

2400

CFW -4000

4000

15

3600×1800×3100

2600

CFW-5000

5000

22

3900×1900×3300

2800

CFW -6000

6000

30

4100×2000×3500

3000

CFW-8000

8000

37

4300×2200×3700

4000

It is suitable for the raw materials that need to concentrate, mix and dry at low temperature (for example, biochemistry products in chemical, pharmaceutical and foodstuff industries. Particularly it is suitable for the raw materials that are easy to oxidize, volatilize and have strong heat sensitive and toxic and not permitted to destroy its crystal in drying.1. The equipment maintenance needs to have professionals, professionals need to hold the relevant nationally recognized operation certificate, and the maintenance personnel need to go through the maintenance training of the supplier. 2. In principle, it is not allowed to change the structure of the equipment during the maintenance process, and if it is necessary to change, it must communicate with the supplier and obtain authorization. 3. If the parts are damaged, the accessories of the same brand and model need to be replaced, such as the equipment damage and other problems caused by the replacement of different brands and models of accessories, the supplier will not be liable. 4. Users need to formulate relevant operation and maintenance procedures to ensure the long-term stability of equipment use. Maintenance personnel should carry out regular or irregular maintenance according to the requirements of the regulations. And the maintenance personnel should be relatively fixed to achieve the best working state of human and machine combination. 5. The reducer is refueled regularly, and the oil level should be high to the center of the oil mark. 6. After the reducer is carried for the first 150 hours, the lubricating oil must be replaced for the first time. Residual oil should be removed during replacement. Replace every 6 months thereafter. 7. The bearing is filled with grease, and it is checked and replenished every 6 months. 8. Regularly check and adjust the tightness of the chain and triangle belt; and apply mechanical oil to the chain.

Contact us

Please feel free to give your inquiry in the form below We will reply you in 24 hours